Street Legal Turn Signal Kit


Lights and Mounts
Street Legal Turn Signal Kit
If you have been looking for a street legal turn signal kit for your UTV or Side By Side, this kit has everything you will need. Whether you've got a Polaris RZR, a Can-Am Commander, Polaris Ranger or virtually any Side By Side out there, this kit makes it much easier to accomplishing the turn signal portion of making your UTV street legal.


NOTE:See options section above to purchase additional LED turn signal lights. The kit comes standard with 2 amber and 2 red super bright LED lights.

****Some Polaris Rangers and Can Am Commanders require additional mounting hardware. All other machines (all RZRs, older Rangers, Teryx and virtually all other UTVs) use the standard mounting kit. SEE OPTIONS ABOVE.****

This LED Turn Signal kit contains:
-Wire and Connector Kit
-2 Amber and 2 Red super bright DOT Approved LED turn signal lights (3/4" diameter).
-Turn Signal Stalk w/ pilot light for turn signals and 4-way emergency flashers.
-Fuse and Fuse holder
-Detailed diagram with instructions

This is a 12 volt Surface Mount LED Turn Signal Kit with 2 Surface Mounted 3/4 inch Amber (front) and 2 Surface Mounted 3/4 inch Red (rear) Super Bright DOT approved LED lights (no brackets required). The SM LED light kit comes with a turn signal switch, which has a pilot light for the turn signals and 4-way emergency flashers (hazard warning). The turn signal switch has a pull on flare tab for the 4-way hazard lights and the hardware to mount it to your steering column.

The four Surface Mounted LED super bright lights are 3/4 inch round with an attached rubber grommet for quick mounting. They are surface mounted LED's with a slim-line design for mounting in small spaces (no brackets required). These SM LEDs are DOT approved, meet the P2PC requirements for 45 degree mounting and provide superior light output. They have a Space Saving Design, Hi Impact Acrylic Lens and Housing and are hard wired with Completely Resin Sealed Electronics to eliminate corrosion.

The special LED Electronic Flasher has the 3 pin connections for LOAD, PILOT and POWER.

The kit includes: 2 Amber and 2 Red SM LED super bright lights with grommets, the Turn Signal Switch and the hardware to mount it to your steering column, the special LED Electronic Flasher with mounting hardware, an ATC in-line fuse holder, a 3 amp fuse, the mounting installation instructions, the wiring instructions & diagram, and all the help and support you need from EZ Turn Signal Kits.

This kit can be easily installed, you don't need any brackets for mounting lights, it does not go into any factory wiring, and it is a completely independent system that comes with the wiring diagram and instructions. Each wire has a different color and the wiring diagram shows where each colored wire goes. I include my phone number and e-mail address with the instructions, so if you have any questions about your installation you can contact me.

This kit was originally developed for the Polaris RZR, RZRS, RZR4, XP 900, the 10-14 Ranger EV, 400 & 500 models. Many customers have installed their kits on the Polaris Ranger EV, 400, 500, XP, HD, Diesel, 6x6, RZR, RZR-S, RZR-4, RZR XP 900, RZR XP-4 900 & Crew models, the Yamaha Rhino, the Can-Am Commander, the Honda Big Red MUV, the Kawasaki Mule & Teryx models, and the Arctic Cat Prowler. This kit can be easily installed on any 12 volt Side-by-Side UTV, Golf Cart, Sand Car, Dune Buggy, etc.

This turn signal switch has been installed on thousands of units, very nice and easy to operate. The Motor Vehicle Department and your local police departments will be impressed. Everyone who rides on the street, off road, at the dunes or in congested riding areas, should have turn signals for there added safety.

Total Power Draw: .20 amps, that's less than a quarter of an amp with all four SM LED hazard lights ON!



The SM LED Turn Signal Kit will fit all years for the Polaris RZR, RZRS, RZR4, RZR XP 900, RZR XP-4 900, Ranger XP, HD, Crew, Diesel, 6x6, EV, 400, 500, 700 & 800 models, all years for the Yamaha Rhino 700, 660 & 450 models, all years for the Can-Am Commander 800 & 1000 models, all years for the Honda Big Red MUV, all years for the Kawasaki Teryx & Mule models, and all years for the Arctic Cat Prowler models. (SEE NOTES BELOW) This kit can be easily installed on any Side-by-Side (side x side), Golf Cart, Sand Car, etc.

Note: some like to customize their UTV with Double or Triple lights, order from the drop down box (BELOW) a) Light Options: Double Lights: 4 Amber & 4 Red lights or Triple Lights: 6 Amber & 6 Red lights.

Note: some like amber lights front and rear, order from the drop down box (BELOW) a) Light Options: Amber Kit: All 4 Amber lights or Double Lights All Amber: 8 Amber lights or Triple Lights All Amber: 12 Amber lights.

Note: the 2009-2010 Polaris Ranger 500, the Full Size Ranger 800, 800 Crew & 6x6, and the Ranger Diesel Models use our custom turn signal switch (TSS) mounting strap. This custom strap will allow the tilt steering to have full range of motion with the turn signal switch mounted just under the steering wheel. Order from the drop down box (BELOW) b) TurnSignal Switch: 09-10 Ranger 500 (TSS) Strap ..or.. Ranger XP & HD (TSS) Strap ..or.. Ranger 800 Crew (TSS) Strap ..or.. Ranger 800 6x6 (TSS) Strap ..or.. Ranger Diesel (TSS) Strap ..or.. Ranger Diesel Crew (TSS) Strap.

Note: the Polaris Ranger EV & 400 and the 2011-12 Ranger 500 & 500 Crew use our custom turn signal switch (TSS) mounting plate. This custom plate was designed to mount the turn signal switch below the steering wheel on the plastic shroud. Order from the drop down box (BELOW) b) TurnSignal Switch: Ranger EV & 400 (TSS) Plate ..or.. 11-12 Ranger 500 (TSS) Plate ..or.. Ranger 500 Crew (TSS) Plate.

Note: the Can-Am Commander use our custom turn signal switch (TSS) mounting bracket. This custom bracket was designed to mount the turn signal switch below the instrument cluster on the steering column. Order from the drop down box (BELOW) b) TurnSignal Switch: CanAm Commander (TSS) Bracket.

Note: the Honda Big Red MUV use our custom turn signal switch (TSS) mounting bracket. This custom bracket was designed to mount the turn signal switch below the steering wheel on the dash. Order from the drop down box (BELOW) b) TurnSignal Switch: 09-12 Honda BR MUV (TSS) Bracket.

Note: the 2008-2012 Arctic Cat Prowler with tilt steering, you may want to use a 5" inch hose clamp to mount the turn signal switch.

Note: the 2010-2012 Kawasaki Teryx with the plastic shroud molded up to the steering wheel, you will need to cut some of the plastic to make room for mounting the turn signal switch OR use a 5" inch hose clamp around the plastic shroud.


http://www.sidebysidestuff.com/street-legal-turn-signal-kit.html
$210.68
Street Legal Turn Signal Kit
Item #:SBSS-6027
Availability:Ships in 1-2 business days *FREE SHIPPING*
Price$229.00
Sale Price$210.68
You SaveYou Save: 8%
Mounting Hardware (Turn Signal Switch)*:
Additional LED Lights*:
Quantity:

Product Description

If you have been looking for a street legal turn signal kit for your UTV or Side By Side, this kit has everything you will need. Whether you've got a Polaris RZR, a Can-Am Commander, Polaris Ranger or virtually any Side By Side out there, this kit makes it much easier to accomplishing the turn signal portion of making your UTV street legal.


NOTE:See options section above to purchase additional LED turn signal lights. The kit comes standard with 2 amber and 2 red super bright LED lights.

****Some Polaris Rangers and Can Am Commanders require additional mounting hardware. All other machines (all RZRs, older Rangers, Teryx and virtually all other UTVs) use the standard mounting kit. SEE OPTIONS ABOVE.****

This LED Turn Signal kit contains:
-Wire and Connector Kit
-2 Amber and 2 Red super bright DOT Approved LED turn signal lights (3/4" diameter).
-Turn Signal Stalk w/ pilot light for turn signals and 4-way emergency flashers.
-Fuse and Fuse holder
-Detailed diagram with instructions

This is a 12 volt Surface Mount LED Turn Signal Kit with 2 Surface Mounted 3/4 inch Amber (front) and 2 Surface Mounted 3/4 inch Red (rear) Super Bright DOT approved LED lights (no brackets required). The SM LED light kit comes with a turn signal switch, which has a pilot light for the turn signals and 4-way emergency flashers (hazard warning). The turn signal switch has a pull on flare tab for the 4-way hazard lights and the hardware to mount it to your steering column.

The four Surface Mounted LED super bright lights are 3/4 inch round with an attached rubber grommet for quick mounting. They are surface mounted LED's with a slim-line design for mounting in small spaces (no brackets required). These SM LEDs are DOT approved, meet the P2PC requirements for 45 degree mounting and provide superior light output. They have a Space Saving Design, Hi Impact Acrylic Lens and Housing and are hard wired with Completely Resin Sealed Electronics to eliminate corrosion.

The special LED Electronic Flasher has the 3 pin connections for LOAD, PILOT and POWER.

The kit includes: 2 Amber and 2 Red SM LED super bright lights with grommets, the Turn Signal Switch and the hardware to mount it to your steering column, the special LED Electronic Flasher with mounting hardware, an ATC in-line fuse holder, a 3 amp fuse, the mounting installation instructions, the wiring instructions & diagram, and all the help and support you need from EZ Turn Signal Kits.

This kit can be easily installed, you don't need any brackets for mounting lights, it does not go into any factory wiring, and it is a completely independent system that comes with the wiring diagram and instructions. Each wire has a different color and the wiring diagram shows where each colored wire goes. I include my phone number and e-mail address with the instructions, so if you have any questions about your installation you can contact me.

This kit was originally developed for the Polaris RZR, RZRS, RZR4, XP 900, the 10-14 Ranger EV, 400 & 500 models. Many customers have installed their kits on the Polaris Ranger EV, 400, 500, XP, HD, Diesel, 6x6, RZR, RZR-S, RZR-4, RZR XP 900, RZR XP-4 900 & Crew models, the Yamaha Rhino, the Can-Am Commander, the Honda Big Red MUV, the Kawasaki Mule & Teryx models, and the Arctic Cat Prowler. This kit can be easily installed on any 12 volt Side-by-Side UTV, Golf Cart, Sand Car, Dune Buggy, etc.

This turn signal switch has been installed on thousands of units, very nice and easy to operate. The Motor Vehicle Department and your local police departments will be impressed. Everyone who rides on the street, off road, at the dunes or in congested riding areas, should have turn signals for there added safety.

Total Power Draw: .20 amps, that's less than a quarter of an amp with all four SM LED hazard lights ON!



The SM LED Turn Signal Kit will fit all years for the Polaris RZR, RZRS, RZR4, RZR XP 900, RZR XP-4 900, Ranger XP, HD, Crew, Diesel, 6x6, EV, 400, 500, 700 & 800 models, all years for the Yamaha Rhino 700, 660 & 450 models, all years for the Can-Am Commander 800 & 1000 models, all years for the Honda Big Red MUV, all years for the Kawasaki Teryx & Mule models, and all years for the Arctic Cat Prowler models. (SEE NOTES BELOW) This kit can be easily installed on any Side-by-Side (side x side), Golf Cart, Sand Car, etc.

Note: some like to customize their UTV with Double or Triple lights, order from the drop down box (BELOW) a) Light Options: Double Lights: 4 Amber & 4 Red lights or Triple Lights: 6 Amber & 6 Red lights.

Note: some like amber lights front and rear, order from the drop down box (BELOW) a) Light Options: Amber Kit: All 4 Amber lights or Double Lights All Amber: 8 Amber lights or Triple Lights All Amber: 12 Amber lights.

Note: the 2009-2010 Polaris Ranger 500, the Full Size Ranger 800, 800 Crew & 6x6, and the Ranger Diesel Models use our custom turn signal switch (TSS) mounting strap. This custom strap will allow the tilt steering to have full range of motion with the turn signal switch mounted just under the steering wheel. Order from the drop down box (BELOW) b) TurnSignal Switch: 09-10 Ranger 500 (TSS) Strap ..or.. Ranger XP & HD (TSS) Strap ..or.. Ranger 800 Crew (TSS) Strap ..or.. Ranger 800 6x6 (TSS) Strap ..or.. Ranger Diesel (TSS) Strap ..or.. Ranger Diesel Crew (TSS) Strap.

Note: the Polaris Ranger EV & 400 and the 2011-12 Ranger 500 & 500 Crew use our custom turn signal switch (TSS) mounting plate. This custom plate was designed to mount the turn signal switch below the steering wheel on the plastic shroud. Order from the drop down box (BELOW) b) TurnSignal Switch: Ranger EV & 400 (TSS) Plate ..or.. 11-12 Ranger 500 (TSS) Plate ..or.. Ranger 500 Crew (TSS) Plate.

Note: the Can-Am Commander use our custom turn signal switch (TSS) mounting bracket. This custom bracket was designed to mount the turn signal switch below the instrument cluster on the steering column. Order from the drop down box (BELOW) b) TurnSignal Switch: CanAm Commander (TSS) Bracket.

Note: the Honda Big Red MUV use our custom turn signal switch (TSS) mounting bracket. This custom bracket was designed to mount the turn signal switch below the steering wheel on the dash. Order from the drop down box (BELOW) b) TurnSignal Switch: 09-12 Honda BR MUV (TSS) Bracket.

Note: the 2008-2012 Arctic Cat Prowler with tilt steering, you may want to use a 5" inch hose clamp to mount the turn signal switch.

Note: the 2010-2012 Kawasaki Teryx with the plastic shroud molded up to the steering wheel, you will need to cut some of the plastic to make room for mounting the turn signal switch OR use a 5" inch hose clamp around the plastic shroud.

Categories
Join our mailing list for more special offers and savings!
Friend us on Facebookwe accept discover, mastercard, visa, and amercian express
Side by Side Stuff is an Upfront Merchant on TheFind. Click for info.