Windshields for Polaris Ranger XP 700
(4.5 out of 5 based on 5 reviews) Read Reviews | Write a Review
SSL Secure and
Privacy Guaranteed
SSL Secured
Expert Support
Product Description
Applicability: Fits Full Size
Along your favorite trails, your Polaris Ranger XP 700 or 570 is one bad mamma jamma! Ripping and roaring through the insane terrain, sometimes things can get a little too intense to handle without a windshield protecting the cab. Forget all this mess when you install the Full Folding Windshield by DaBomb Windshields to the front of your UTV. This aftermarket windshield allows you to enjoy the best of both windshield words!
This windshield allows the driver to enjoy full protection where needed paired with the ability to savor free-flowing fresh air with just a simple fold of the windshield. It comes with all the necessary hardware needed to install, including a rubber bumper that sets on the hood to prevent scratching when placed in the fold position. With no more than a screwdriver and wrench required, set-up takes mere minutes, getting you back on the road in no time! From its tight fit for riding and trailering to its heavy-duty Velcro straps, this 100% made in the U.S.A. accessory is a must for any off-road enthusiast.
Features:
Hard Coat Option:
Lexan, though impact resistant, is highly susceptible to scratching and even cleaning it incorrectly can scratch the material. The MR-10 hard coat option covers both the outside and interior of the windshield, prevents scratching and lengthens the life of your windshield. It is also 1/4 inch thick versus the non-coated windshield that is 3/16 inch thick.
Soft Top (no measurement required):
Bend at top so soft top goes over the windshield and ensures no water leaks into the cab.
Hard Top (aftermarket hard top requires measurement):
Custom sized to your aftermarket hard top so the windshield can still fold without removal of top. To measure for aftermarket hard top (see diagram above): Your starting point will be the weld around the roll bar that is above the 2 bolts by the body (see diagram). From there, measure straight up the roll bar to the bottom lip or lowest point of the hard top. If measurement is not listed, we suggest rounding down to the next measurement. Reverse bend so top goes over the windshield and ensures no water leaks into the cab.
PLEASE READ: Upon receipt of your windshield and prior to removing the protective film
View Care Instructions
- 2009-14 Ranger XP 700 / XP 800 and 800 Crew
- 2011-17 Ranger 6x6
- 2011-14 Ranger Diesel
- 2016-21 Ranger Full Size 570 and Crew 570-6 (with round roll bars)
Along your favorite trails, your Polaris Ranger XP 700 or 570 is one bad mamma jamma! Ripping and roaring through the insane terrain, sometimes things can get a little too intense to handle without a windshield protecting the cab. Forget all this mess when you install the Full Folding Windshield by DaBomb Windshields to the front of your UTV. This aftermarket windshield allows you to enjoy the best of both windshield words!
This windshield allows the driver to enjoy full protection where needed paired with the ability to savor free-flowing fresh air with just a simple fold of the windshield. It comes with all the necessary hardware needed to install, including a rubber bumper that sets on the hood to prevent scratching when placed in the fold position. With no more than a screwdriver and wrench required, set-up takes mere minutes, getting you back on the road in no time! From its tight fit for riding and trailering to its heavy-duty Velcro straps, this 100% made in the U.S.A. accessory is a must for any off-road enthusiast.
Features:
- 2 year warranty against manufacturer defect, product clouding or discoloring
- Secures tight in down position for towing and riding
- All hardware and installation instructions are included
- Takes no more than a screwdriver and wrench to install
- Bumpers keep windshield from touching hood when in the folded position
- Heavy duty Velcro straps secure windshield when in folded position
- Made in the U.S.A.
Hard Coat Option:
Lexan, though impact resistant, is highly susceptible to scratching and even cleaning it incorrectly can scratch the material. The MR-10 hard coat option covers both the outside and interior of the windshield, prevents scratching and lengthens the life of your windshield. It is also 1/4 inch thick versus the non-coated windshield that is 3/16 inch thick.
Soft Top (no measurement required):
Bend at top so soft top goes over the windshield and ensures no water leaks into the cab.
Hard Top (aftermarket hard top requires measurement):
Custom sized to your aftermarket hard top so the windshield can still fold without removal of top. To measure for aftermarket hard top (see diagram above): Your starting point will be the weld around the roll bar that is above the 2 bolts by the body (see diagram). From there, measure straight up the roll bar to the bottom lip or lowest point of the hard top. If measurement is not listed, we suggest rounding down to the next measurement. Reverse bend so top goes over the windshield and ensures no water leaks into the cab.
PLEASE READ: Upon receipt of your windshield and prior to removing the protective film
- Inspect for any damages, including scratches protruding through the protective film
- Ensure product satisfaction
- Confirm correct fitment
View Care InstructionsCustomer Reviews
Product Reviews
Folding windshield, October 30, 2019 Satified, September 25, 2019 very pleased with product, July 23, 2019
Great windshield just not for me, April 24, 2019Posted By: Austin Bastinelli - verified customer
2 people found this review helpful
I purchased the scratch resistant windshield with the extra layer of what looks like a really thick screen protector on the outside. This is a great product, the hardware could be made of stainless but otherwise is good quality. The video showing how to install really made that process a breeze. Probably took an hour total from taking out of the box to being done and some of that time was spent moving my Wet Sounds speaker bar back so the windshield wouldn’t hit it.
My main issues with this windshield is that it blocks al the wind and makes a sort of vortex that picks up all the sand and covers all the occupants in dust and sand while driving. It’s so bad that if your not wearing glasses you can’t drive. You could fold the windshield down but it doesn’t fasten while in the down position. The windshield while in the down position is actually wider than the front of my ranger and if your trail riding a lot like I do the first time it catches a branch or something it’s going to break.
So I pulled it off and bought the largest half windshield that this same company sells and have been very happy with it.
2 people found this review helpful
I purchased the scratch resistant windshield with the extra layer of what looks like a really thick screen protector on the outside. This is a great product, the hardware could be made of stainless but otherwise is good quality. The video showing how to install really made that process a breeze. Probably took an hour total from taking out of the box to being done and some of that time was spent moving my Wet Sounds speaker bar back so the windshield wouldn’t hit it.
My main issues with this windshield is that it blocks al the wind and makes a sort of vortex that picks up all the sand and covers all the occupants in dust and sand while driving. It’s so bad that if your not wearing glasses you can’t drive. You could fold the windshield down but it doesn’t fasten while in the down position. The windshield while in the down position is actually wider than the front of my ranger and if your trail riding a lot like I do the first time it catches a branch or something it’s going to break.
So I pulled it off and bought the largest half windshield that this same company sells and have been very happy with it.
PLEASED, November 11, 2018Click here to review this product
(Reviews are subject to approval)
(Reviews are subject to approval)
